Jungheinrich ETV 216 Operating Manual | PDF | Truck - Scribd
The accelerator pedal was pressed when the truck was turned on. Action: Restart the truck without touching the drive pedal. Error 1908.1 - Seat Belt/Seat Switch Error:
Fasten the seat belt and check the seat switch functionality.
: Switch the truck off and on again to see if the message clears. jungheinrich etv 216 error codes
Park the truck in a safe location and leave it powered on but completely idle. This allows the cooling fans to run. Check the controller area for dust buildup and clean the cooling fins with compressed air. 4. Code 2201: Lift Hydraulics Timeout / Sensor Error
This error relates to a motor controller/interface board (part number 51169229). A technician reported: "An overseas client of mine has shortly ordered a spare part (Motor controller/Interface Board) for his ETV216 2013 Model. ... Now that he has finally received it and was trying to installing, he keeps receiving the above mentioned error (0802)".
For the reach truck, error codes (or "event messages") are typically displayed as four-digit codes that pinpoint issues in specific function groups like travel, lifting, or steering. Common Error Codes & Meanings Jungheinrich ETV 216 Operating Manual | PDF |
| Code | Likely cause | Immediate actions | |---|---:|---| | E001 / 001 | Controller power fault / CAN bus communication error | Cycle power; check main connectors and fuses; inspect CAN wiring and terminations. If intermittent, log occurrence and replace/repair damaged cable or module. | | E010 / 010 | Battery voltage low / undervoltage | Check battery state-of-charge and connections; charge or replace battery; inspect charger and battery isolator. | | E011 / 011 | Battery voltage too high / overvoltage | Verify charger output and battery configuration; check for faulty sensors or charger regulation. Remove charging source if unsafe. | | E020 / 020 | Traction motor fault | Check motor connections, thermal switches, and motor brushes (if applicable); inspect for overheating/mechanical jam. Replace motor controller if diagnostics indicate. | | E030 / 030 | Brake circuit fault / parking brake not engaged | Inspect brake switch, wiring, and hydraulic/electric brake actuator; verify brake interlock sensor. Do not operate until brake is confirmed functional. | | E040 / 040 | Throttle / accelerator sensor fault | Check pedal position sensor (potentiometer/Hall) and wiring; calibrate or replace sensor/module. | | E050 / 050 | Steering/steer-angle sensor fault | Inspect steering angle encoder and cabling; calibrate steering sensor or replace if failed. | | E060 / 060 | Transmission or gearbox sensor fault | Check shift actuator and sensors; verify oil level and mechanical linkages. | | E070 / 070 | Temperature warning / thermal limit reached | Allow unit to cool; check cooling fans/vents, coolant (if liquid-cooled) and ambient conditions; investigate cause of overheating. | | E080 / 080 | Hydraulic system fault / pressure sensor error | Check hydraulic fluid level, pump function, and pressure sensors; remedy leaks and replace faulty sensor. | | E090 / 090 | Safety interlock / emergency stop triggered | Reset emergency stop, verify E-stop circuit and switches, inspect safety interlocks and wiring. Do not bypass safety devices. | | E100 / 100 | Seat switch / operator presence sensor fault | Inspect seat switch and wiring; replace if intermittent or failed. | | E110 / 110 | CAN bus timeout / module not responding | Check network wiring, terminators, and module power supply; replace non-responsive module. | | E120 / 120 | Charger/charging circuit fault | Inspect charger, contactors, fuses, and battery connector; replace defective charger components. | | E130 / 130 | Fuse or relay failure | Inspect and test fuses and relays; replace failed items and investigate root cause (short circuit, overload). | | E140 / 140 | Internal ECU fault / memory error | Attempt ECU reset; if persistent, replace ECU and restore configuration/calibration from service data. | | E150 / 150 | Software/version mismatch / configuration error | Verify software versions across modules; update with manufacturer tools and reconfigure parameters as required. | | E160 / 160 | Sensor signal out of range | Identify which sensor flagged; inspect wiring and sensor, test signal, and replace or recalibrate. | | E170 / 170 | CAN bus BUS-OFF / high error counters | Inspect spurious noise sources, wiring damage, short circuits; repair bus and clear error counters. | | E180 / 180 | Battery temperature sensor fault | Check battery temp sensor and wiring; do not charge if sensor indicates unsafe temperature. | | E190 / 190 | Powertrain general fault | Run full diagnostic with Jungheinrich service tool; follow suggested test flow to isolate subsystem. |
According to System Error Code Documentation , many system errors refer to controller or communication issues.
The code appears as soon as you touch the steering wheel, making the truck difficult or impossible to steer properly. : Switch the truck off and on again
Park the truck in a safe location, turn off the ignition, and allow the motor to cool down for at least 20–30 minutes. Check the motor cooling vents for dust or plastic wrap blockages. Lift and Hydraulic Errors (2000 Series) Error Code 2011: Hydraulic Valve Fault
If your ETV 216 displays a code, it typically falls into one of these categories: Operator & Safety Errors
When your reach truck stops operating and displays a code, understanding what that code means can be the difference between a two-minute reset and expensive, unnecessary downtime. This guide breaks down the most common Jungheinrich ETV 216 error codes, what they mean, and how to resolve them safely. Understanding Jungheinrich Error Code Structures